CLI Switch: Unterschied zwischen den Versionen
Zur Navigation springen
Zur Suche springen
6vffdh (Diskussion | Beiträge) |
6vffdh (Diskussion | Beiträge) |
||
| Zeile 117: | Zeile 117: | ||
stacking enable | stacking enable | ||
| − | |||
show flash | show flash | ||
| − | |||
show version | show version | ||
| − | |||
boot system flash primary | boot system flash primary | ||
| − | |||
boot system flash secondary | boot system flash secondary | ||
| − | |||
boot set-default flash secondary | boot set-default flash secondary | ||
| − | |||
show configuration pending | show configuration pending | ||
| − | |||
configuration purge-pending-config | configuration purge-pending-config | ||
Version vom 6. März 2023, 20:49 Uhr
HP 2920
- Aruba JL321A 2930M-48G Stacking Switch
- Aruba Stacking Module JL325A
- Aruba 10 G SFP+ Module J9150D
- Aruba JL355A 2540-48G-4SFP+ Switch
- Anschließen über COM Port USB Micro Kabel an die Console.
Befehle
Setup und Show Befehle:
SWITCH1# setup
SWITCH1# config
SWITCH1# show vlan
show vlans ?
SWITCH1# show config
SWITCH1# show trunk show trunks ?
ip routing show ip show lacp show interafaces
show running-config
sh ru
show cdp neighbors detail
show mac-address
show interface 51
SWITCH1# show vlan ports 20-24 detail SWITCH1# show vlan ports 3 detail SWITCH1# show vlan ports trk2 detail SWITCH1# show vlan ports all detail
"Config" Befehle:
SWITCH1# config
VLANs anlegen
SWITCH1(config)# vlan 10 name zSERVER SWITCH1(config)# vlan 20 name zCLIENT SWITCH1(config)# vlan 30 name zWLANAP SWITCH1(config)# wr mem
Trunk-Port erstellen an einzelnen Port
SWITCH1(config)# vlan 1 untagged 48 SWITCH1(config)# vlan 10 tagged 48 SWITCH1(config)# vlan 20, 30 tagged 48 SWITCH1(config)# wr mem
Trunk-Port mit LACP erstellen an eine Port Gruppe und Zuweisung von Vlans:
Aruba-Stack-2930M(config)# trunk 2/47,3/47 trk6 lacp Aruba-Stack-2930M(config)# interface trk6 Aruba-Stack-2930M(eth-Trk6)# untagged vlan 1 Aruba-Stack-2930M(eth-Trk6)# tagged vlan 10,20,30,40,50 Aruba-Stack-2930M(eth-Trk6)# wr mem
SWITCH1(config)# vlan 20, 30 tagged 48 SWITCH1(config)# wr mem
Trunk-Port löschen
no trunk 1/A1, 1/A2 wr mem
Access-Ports erstellen
SWITCH1(config)# vlan 10 untagged 1-10 SWITCH1(config)# vlan 20 untagged 11-20 SWITCH1(config)# vlan 20 untagged 21-30 SWITCH1(config)# wr mem
Vlan von dem port löschen
no vlan 3 untagged 37 no vlan 4 tagged 37
Andere Variante "config" interface oder Gruppe:
SWITCH1(config)# interface 31-40 SWITCH1(eth-31-40)# untagged vlan 10 SWITCH1(eth-31-40)# tagged vlan 20 SWITCH1(eth-31-40)# tagged vlan 30 SWITCH1(eth-31-40)# wr mem SWITCH1(eth-31-40)# exit SWITCH1(config)#
VLAN vom Port entfernen
SWITCH1(config)#interface 1 SWITCH1(eth-1)# no untagged vlan 10 1:These ports are moved to default VLAN.
- Test Befehle
ping 192.168.10.100
Stacking Switch Aruba Befehle
stacking enable show flash show version boot system flash primary boot system flash secondary boot set-default flash secondary show configuration pending configuration purge-pending-config
